Plumbing Basics: The First Step for Bathtub Installation
Plumbing Basics: The First Step for Bathtub Installation
Blog Article
Are you in search of facts around How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Installing a bathtub isn't specifically rocket science, but it does need strong plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a reasonably tough project. If the old tub is readily available, the job can move easily; if you need to open a wall to eliminate the old bathtub as well as place the new bath tub, the job is much harder. In either instance, the task is within a house handyman's skills, although you will require an assistant to move out the old tub as well as set in the brand-new one. See to it you have actually certified yourself for the work and are comfortable attempting it. Instead of hiring a contractor to take control of a halfway-completed task, it is much better to think about utilizing one before you start. Chances are you may need a professional plumber to make tube links.
This short article will certainly aid you mount a brand-new bath tub in your shower room if you have currently gotten a brand-new tub as well as do not need to alter the setup of your previous supply of water pipelines.
Your tools and product list should comprise the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your setup, after that the first thing you must do is detach the water supply. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The process of eliminating the existing faucets can be rather troublesome due to the limited gain access to that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a cloth ready for the continuing to be water that will come from the pipelines. When the supply pipelines have been removed, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the single faucets from turning throughout this process. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing compound.
Prior to going on to fit the new taps, contrast the pipe connections on the old faucets to the new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic adapter to prevent damages to the string. One end of the port fits on the plastic tail of the tap and the other end offers a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly need reducing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the placing hole in the bath/basin making certain that the washers are in area in between the tap and the sink. Protect the tap in place with the maker offered backnut. Once the tap is securely in position, the supply pipes can be attached to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with typical tap adapters. The previous kind should be linked to the faucet ends initially, tightening just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Installing the Bath tub
Making use of both wooden boards under its feet, place the tub in the needed placement. The wooden boards are helpful in evenly spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto 4 little points.
The next goal is to make certain that the tub is leveled all round. This can be achieved by inspecting the spirit level as well as adjusting the feet on the bathtub until the level checks out degree.
To install faucets, fit all-time low of the outermost flexible tap port to the appropriate supply pipe by making a compression sign up with; then do the same for the various other faucet.
Switch on the water system as well as inspect all joints and also brand-new pipework for leaks as well as tighten them if essential. Fill the bathtub and likewise examine the overflow outlet and the normal outlet for leakages.
Finally, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and also securing around the bath tub must wait until the tub has actually been used a minimum of when as this will certainly settle it right into its last setting.
Planning for the Installment
Firstly, the supporting structure supplied with the bath should be fitted (if called for) according to the supplier's directions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to make certain that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets device to avoid stress on the bath tub.
Fit the versatile faucet connectors to the bottom of both taps making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet with the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you use every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom must now be ready to be fitted in its last placement.
Tiling Around the Tub
In the area where the bathroom satisfies the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to break a rigid seal, creating the water to permeate the wall in between the bathroom as well as the tiling, bring about problems with moisture as well as feasible leakages to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes and cartridges, and also are capable of securing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to load, you can load it with twists of soaked paper or soft rope. Remember to constantly load the tub with water prior to sealing, to permit the movement experienced when the tub is in usage. The sealant can crack rather early if you do not consider this activity prior to sealing.
Additionally, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise quickly readily available on the marketplace. It is a good idea to fit the floor tiles using water-resistant or water resistant glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I ran across that blog entry on How to Install a Bathtub Yourself when doing a search on the web. Loved our review? Please share it. Help others locate it. Thanks for your time invested reading it.
Today's problem, today's fix! Report this page